토너 교체방법 등


gcg : 배우고 갑니다
나 : 잘 봤습니다!
가조풍월 : 잘배우고갑니다
마호성 : 감사합니다!
고제철 : 복사기 인쇄물에서 토너가 벗겨지는데 왜 그러지요 궁금합니다.... 010-4696-9642

How to replace the Samsung CLX-3185 toner cartridges

Step by step video showing you how to change the Samsung CLX-3185 toner cartridges.
jorg Manowar : How do we reset the toner cartridges. We usually get messages that toner is low but this is usualy not true. Toner could be as high as 35% and obviously it can be properly used. The reason is that Samsung wants us to buy more often their probucts byt throwing away the "old" ones even If they still can work. This is called planned obsolescence.
Mr Freeze : and if it's a compatible printer cartridge, you will surely get the "incompatible black toner" ! awesome!

Samsung CLP310 320 360 CLX Drum unit Rebuilding Instructions

How to remanufacture and reset Samsung OPC Photoconductor Drum Unit for CLP-310 CLP-315 CLP-320 CLP-325 CLP-360 CLP-365 CLX-3170 CLX-3175 CLX-3180 CLX-3185 CLX3305 CLX3300 XPRESS-460W CLT-R409 CLT-R407 CLT-T406

- Activare Subtitles in your language! -

to reset the drum without the thermal fuse put a small piece of copper across the terminals of the resistor. Close the door and plug the printer in. It will initialize, followed by a flash of lights,
It will reset itself as it is unable to "blow" the fuse.
At this point unplug power and take out the holder with the resistor again. Take the small copper wire off and put the holder back in. Close the door and let the printer startup.

CLT-R406, CLT-R407 and CLT-R409 drum units are different and not interchangeable, but the remanufacturing instructions are the same.

Things needed:
- Screwdriver
- Drum
- Resistor for use in Samsung drum unit

How to fix Samsung printer with error red light:
The drum has a resistors that is used to calculate toner coverage. The resistors contains calculated limitation that was managed by Samsung. If toner coverage is 5%, the resistor is delivered 20000 black pages and 5000 color pages.
When the resistors overload its calculated limitation, the printer will be locked and will send an error message. Change this resistor to solve the problem.

For any question or suggestion leave a comment
--------------------------------------------
Link Accessori srl
Via Beverara 224/7
40131 BOLOGNA (Italy)
http://www.linkaccessori.it
email: link.accessori@libero.it

other links:
http://www.emmegiricambi.it/
http://www.samsung.com/it/consumer/pc...






-------------------------------------------------------------------------
lloyd dobbler : Thank you very much for this video. I was able to fix "image ghosting" on a Samsung CLP-315W by following your instructions to clean the charge roller with water. Imaging Unit was only at 1100pgs, 84% life remaining, but living in dry climate(Denver, CO) made the charge roller(and foam roller) ineffective at removing excess image toner.
Imaging unit drum was diagnosed as culprit by measuring 7.5 vertical inches between original image and ghosted image. Again, 10,000 thanks.
Comfort Zone : The green component being replaced is IS NOT A RESISTOR, it is a THERMAL FUSE. when the page count is reached, the printer controller sends a high current spike to this fuse to blow it and once it is blown, the printer knows that this is a used drum unit. you can check the continuity of this component with an ohm meter. It should have a number on it to give you the current rating. To get you going you can just jump it with a wire, but replace it afterwards with a fuse for so that when the printer sends a current spike, this fuse gets blown instead of something in your controller. Just google thermal fuse and you will see the image of this component. This component costs only a few pennies, many people on ebay are selling it for a few dollars. Alternatively you can use a very very thin single wire strand taken out from an electrical wire and solder across the two points, this will serve as a fuse.
Update: the green component on my image drum says 1/16A, meaning it is a .0625 Amp. fuse. I took a single wire strand from an ear phone wire, the wire strands from that wire are very very thin and I replaced the fuse with that wire.
Martin Dorrance : Thanks for your videos. I have followed your steps and it became obvious that my smudgy printing was due to waste toner everywhere after printing envelopes etc. After rebuilding I am still getting big patches of no or feint print but some decent print across the full page in places. Also, any pictures including the test page come out as a yellow smudge. Any ideas please?
Penurious Sierra : I found that my imaging unit had an overflowing toner that stacks up from the top. Following your guide, I cleared out the waste toner tank (there was a TON of powder). Let's see what happens.
Mtech Toner : Thank you for sharing. Had all that I needed to know to fix my outdated printer.

...